Tools

The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor. NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.

It's a spoon! It's a fork! Park's Stainless-Steel Spork is a take-along culinary multi-tool made from high-quality, rustproof stainless steel with a comfortable vinyl-coated handle. Who said nutrition has to come from energy bars? Pack your favorite eats and Park's Spork for enjoying on-the-ride snacks and mid-repair munchies in style! The Spork has a hole for carrying it on a keychain or hanging it on your workbench.

The Cyclone Chain Scrubber brushes are replaceable. The RBS-5 brush set includes the large side scrubbing brush, two roller brushes, and two wicking foam blocks.

A handy tool designed to make installation and removal of bicycle electronic shifting wires and batteries quick and easy. - Durable composite body is durable and prevents scratching of expensive components - Angled Shimano Di2 E-TUBE ends allow for both installation and removal in tight spaces - Universal coin cell tool helps remove and install battery covers on SRAM eTap

Designed and built to remove and install the lockring that retains front chainrings found on Shimano STEPS e-bike motors. - Fits Shimano STEPS E6100, E7000, E8000 and E9000 e-bike motor systems - For lockrings with 54mm outside diameter and 16 notches - Replacement for Shimano TL-FC39 tool - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - Constructed of 4140 heat-treated steel and plated for long life

Designed and built to remove and install the direct mount lockring that retains front chainrings found on some Specialized, Cannondale and FSA modular cranks. - Fits chainring of Specialized, Cannondale and FSA - For lockrings with 47–48mm outside diameter and 4 or 8 notches - Fits both 4 notch (FSA and Cannondale) and 8 notch (Specialized) lockrings - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - Constructed of 4140 heat-treated steel and plated for long life

Your new favorite tool for truing and building wheels. The CSH-1 securely holds spokes in place during spoke tension adjustment to prevent wind-up of round and bladed spokes, as well as rotation of straight-pull spokes. The versatile head can grip spokes in multiple positions for optimal leverage and hand positioning. Constructed of forged heat-treated steel with comfortable dual-density grips. - Compatible with round and bladed spokes 2.3 mm (13 gauge) wide or less - Compatible with J-bend and straight pull spokes

Clean out or restore damaged threads in crank arms with Park Tool's Pedal Taps. They're sold as a set of right and left hand threads. Made of high carbon steel, precision ground, and hardened to stay sharp, they cut easily and fit all conventional tap handles. • Includes a set of 2 taps, 9/16" x 20 tpi • Made of high carbon steel, precision ground, and hardened to stay sharp • Fits all conventional tap handles The tap drill size for a 9/16-inch x 20 tpi thread is nominally 33/64-inch.

The small and handy RR-12.2 Tape Measure features a tough composite housing with an integrated belt clip and both metric and SAE readings up to 350 centimeters or 12 feet. Measurement can be locked in place using the thumb lock or the handy quick-stop button. - RR-12.2 features a new body design with a handy-quick stop button on the bottom, allowing the user to temporarily lock the tape into place with their index finger - Maximum length: 350 cm | 12 ft. - Markings: 1 mm | 1/32" (up to 6") | 1/16" (over 6") - The RR-12.2 features a new body design with a handy-quick stop button on the bottom, allowing the user to temporarily lock the tape into place with their index finger - Metric and SAE readings up to 350 centimeters or 12 feet - Markings: 1 mm | 1/32" (up to 6") | 1/16" (over 6")

Professional quality T-Handle hex wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or oversized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions

World-famous Park Tool quality wrapped up in a combination metric wrench. Features both open and 12-point two-way ratcheting box ends. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful!

Having trouble getting at internal spoke nipples? Park's Square Socket Internal Nipple Spoke Wrench comes to your rescue. The extra-long socket fits recessed nipples on most deep-section aero wheels. And, the ergonomic handle is comfortable even after you've built wheels for the entire team.

Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.

Forged with Chrome Vanadium (CR-v) steel, precision ground, heat-treated, plated and polished. The PAW-6 opens to 24mm and features a laser engraved measurement scale and dipped blue handle for comfort.

The 15-inch SWB-15 is a forged steel breaker bar with a 3/8-inch square drive head that pivots 180º. Features a long, knurled handle, which is extremely useful when extra leverage is needed to remove stubborn fasteners.

Forged and machined, the ZP-5 is ideal for closely cutting zip ties and many other materials in tight spaces.

Park Tool's Crown Race Cutter Adaptor is used in conjunction with the CRC-1 Crown Race Cutting Tool (sold separately) to machine 39.8mm crown race seats (1.5” standard) on tapered forks with 1-1/8” steerer tubes. It includes a precision-machined adaptor body and a 39.8mm high-speed steel crown race cutter. The CRC-15 will work on forks with a maximum 1.5-inch taper of 4.25 inches.

Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4T was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Bench Top Mount sits firmly on any flat surface - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)

Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.

Park Tool's SW-11 is a forged, double-ended spoke wrench designed to fit select Campagnolo wheels. Precision machined, plated and vinyl dipped for comfort and long life. It fits Campagnolo 5.5mm and 6.0mm hex spoke nipples.

Specially designed for crank bolts, freehub removals and pedal installs and removals, Park's Hex Tools are built for speed, leverage and comfort. Their super-precise hex heads and dual-density, ergonomic handle mean the HTs may soon become your new favorite tools.

Park's Tire Seating Tool is designed to quickly seat the bead on stubborn tires. During inflation some tire beads can slip below the rim edge and become difficult to pull out and align. The PTS-1 comes to the rescue with its non-slip jaws and vinyl-coated handles that provide plenty of leverage for pulling out the tire. Plus, it's adjustable to fit various tire widths.

The BKM-1.2 Hydraulic Brake Bleed Kit will bleed most models of mineral oil-based hydraulic bicycle disc brakes, including models made by Shimano®, Magura®, TRP®, Tektro®, Trick Stuff®, SRAM® DB8, Campagnolo®, Promax®, and Clarks®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKM-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, a bleed funnel, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: -  Two 20 mL syringes -  Two hose assemblies with shutoff clips -  One hose assembly with integrated fitting for bleed nipples such as those found on Shimano® mineral oil brake systems -  One open-ended hose assembly -  Bleed funnel with stopper -  Two 10 mm/12 mm universal bleed blocks -  Two 11 mm bleed blocks -  Two adjustable syringe holders -  M4 x 0.7 adapters — SRAM® DB8, Trick Stuff®, Campagnolo® (x2) -  M5 x 0.8 adapter — Formula™ Cura™, Tektro®, Hayes® (x2) -  M6 x 0.75 adapter — Magura® -  M6 x 1.0 adapters — universal (x2) -  M6 x 1.0 adapter — Promax® -  M7 x 0.75 adapter — Shimano® -  Hose compression sleeve — universal -  Fluid disposal bag -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKM-1.2 is for mineral oil-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For brakes using DOT fluid use the Park Tool BKD-1.2 Hydraulic Brake Bleed Kit — DOT.

"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings: • Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose • Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS • Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm • Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire • Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes Also included: • Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing • Guide magnet — routes guide cables through the frame from the outside"

Bicycle disc brake rotors can become warped from extensive use, excessive heat, or impact. Even new disc rotors may not always be perfectly straight, causing annoying pad rub and affecting performance. The Park Tool DT-2.2 is specially designed and precisely manufactured to gently adjust bent bicycle disc brake rotors. The DT-2.2 features one long slot and two short slots for maximum compatibility with any rotor design or thickness up to 2.5 mm. Constructed from high quality steel with a vinyl dipped handle for comfort. Compatible with rotors up to 2.5 mm thick

Park's Tire and Tube Repair Kit is a riding essential. It features Park’s glueless Super Patch Kit and strong nylon Tire Levers for quick and easy flat repairs. The kit comes with 3 levers, 6 patches in a small container, and a piece of sandpaper (for roughing the tube to prepare it for patching).

The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.

Securely holds any of Park's TS-2, TS-2.2, and TS-2.2P Professional Wheel Truing Stands and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.

Designed and built specifically for a wide variety of bicycle Torx compatible work, the THT-1 is a set of eight common sizes of professional quality T-Handle star-shaped wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite Torx compatible set, the THT-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - T6, T8, T10, T15, T20, T25, T30 and T40 Torx compatible wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

Forged and precisely machined, the high leverage LP-7 Utility Pliers include an integrated cutting blade and soft touch grips.