Tools

Designed and built to remove and install the lockring that retains front chainrings found on Shimano STEPS e-bike motors. - Fits Shimano STEPS E6100, E7000, E8000 and E9000 e-bike motor systems - For lockrings with 54mm outside diameter and 16 notches - Replacement for Shimano TL-FC39 tool - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - Constructed of 4140 heat-treated steel and plated for long life

Designed and built to remove and install the direct mount lockring that retains front chainrings found on some Specialized, Cannondale and FSA modular cranks. - Fits chainring of Specialized, Cannondale and FSA - For lockrings with 47–48mm outside diameter and 4 or 8 notches - Fits both 4 notch (FSA and Cannondale) and 8 notch (Specialized) lockrings - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - Constructed of 4140 heat-treated steel and plated for long life

World-famous Park Tool quality wrapped up in a combination metric wrench. Features both open and 12-point two-way ratcheting box ends. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful!

Having trouble getting at internal spoke nipples? Park's Square Socket Internal Nipple Spoke Wrench comes to your rescue. The extra-long socket fits recessed nipples on most deep-section aero wheels. And, the ergonomic handle is comfortable even after you've built wheels for the entire team.

Clean out or restore damaged threads in crank arms with Park Tool's Pedal Taps. They're sold as a set of right and left hand threads. Made of high carbon steel, precision ground, and hardened to stay sharp, they cut easily and fit all conventional tap handles. • Includes a set of 2 taps, 9/16" x 20 tpi • Made of high carbon steel, precision ground, and hardened to stay sharp • Fits all conventional tap handles The tap drill size for a 9/16-inch x 20 tpi thread is nominally 33/64-inch.

The small and handy RR-12.2 Tape Measure features a tough composite housing with an integrated belt clip and both metric and SAE readings up to 350 centimeters or 12 feet. Measurement can be locked in place using the thumb lock or the handy quick-stop button. - RR-12.2 features a new body design with a handy-quick stop button on the bottom, allowing the user to temporarily lock the tape into place with their index finger - Maximum length: 350 cm | 12 ft. - Markings: 1 mm | 1/32" (up to 6") | 1/16" (over 6") - The RR-12.2 features a new body design with a handy-quick stop button on the bottom, allowing the user to temporarily lock the tape into place with their index finger - Metric and SAE readings up to 350 centimeters or 12 feet - Markings: 1 mm | 1/32" (up to 6") | 1/16" (over 6")

Professional quality T-Handle hex wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or oversized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions

Your new favorite tool for truing and building wheels. The CSH-1 securely holds spokes in place during spoke tension adjustment to prevent wind-up of round and bladed spokes, as well as rotation of straight-pull spokes. The versatile head can grip spokes in multiple positions for optimal leverage and hand positioning. Constructed of forged heat-treated steel with comfortable dual-density grips. - Compatible with round and bladed spokes 2.3 mm (13 gauge) wide or less - Compatible with J-bend and straight pull spokes

- Used when facing BB86/92 bottom bracket shells and reaming is not required - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)

They always say, the right tool for the right job. Park's P-handled Torx Wrenches are available in T6, T8, T10, T15, T20, T25, T30 and T40 sizes. They feature offset handles made from durable nylon with a comfortable, ergonomic design. The wrenches are made of high-torque industrial steel for excellent durability.

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 23mm size fits Shimano 15mm through-axle hubs. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.

Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.

Park's AWS-8 Hex Wrench Set features Bondhus balldriver ends, which facilitate use when the tool is at an angle to the bolt. This is great for working in hard-to-reach areas, such as reaching water-bottle-cage screws. The AWS-8 has 4, 5, and 6mm wrenches, which are the most common bicycle bolt sizes. Plus, its Y shape and vinyl coating provide excellent leverage and comfort.

A puncture in your tubeless tire doesn't have to be a death sentence for your ride. This handy carry-along tool repairs small punctures and cuts in tubeless bicycle tires without removing the tire from the rim, getting you back on the trail in no time. The TPT-1 easily plugs the hole by inserting one of the 5 included vulcanized rubber plugs into the puncture. This shrinks the puncture down to a manageable size, allowing the tubeless sealant to do its job and reestablish a seal. The unique sliding plug retainer holds the plug in place and prevents it from being pulled back out as the tool is removed. Everything is stored in a compact package that fits easily in a saddlebag or backpack pocket. - Includes 5 vulcanized rubber plugs (refills available — part #2370K) - Dimensions: 89 x 27 x 40 mm (3.5" x 1.1" x 1.6") - Weight: 79 grams (2.8 oz.) with plugs NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.

Also called a sleeping hub, the Dummy Hub slides into rear dropouts and replaces the rear wheel for chain cleaning and transport. The DH-1 works with all derailleur and 1/8" chain. The unique design allows the bike to be shifted and works with open dropout and thru-axle frames up to 12mm.

Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.

Park's Fixed-Gear Lockring Wrench features 2 different radius hooked spanners for a precise fit, and easy removal and tightening of most fixed-gear lockrings. The HCW-17 fits rings with an outside diameter of 41 to 44mm. It also fits BMX cassette hub lockrings with external notches.

A sturdy bicycle cleaning brush with a unique angled and contoured shape – perfect for cleaning cassettes and freewheels as well as tires. With a strong ergonomic handle and stiff nylon bristles, the GSC-4 scrubs away the toughest muck and mess.

The BBP-1.2 quickly and accurately installs bottom bracket bearings, cups and adapters into press fit bottom bracket shells. The complete set of precision-machined bushings matches up with most common bottom bracket cup dimensions. The press assembly features a comfortable handle, oversized shaft, and magnetic back plate for quick and easy assembly. - The complete set of precision-machined bushings match up with most common bottom bracket cup dimensions - The press assembly features a comfortable handle, oversized shaft, and magnetic back plate for quick and easy assembly - Magnetic quick-release design allows for fast installation and removal of tool - Organized in a convenient storage case - Compatible with bottom bracket shell widths from 68mm to 150mm 6 sets of precision-machined bushings (in 9 sizes) to fit these bottom bracket configurations: - 386EVO - BB30 - BB86 - BB90 - BB92 - BB95 - BB121 - BMX Mid - BMX Spanish - OSBB - PF41 - Press Fit 24 - PressFit GXP® - BBright™ Direct Fit - PF30 BBright™ Press Fit - Shimano® Press Fit - All Press Fit DUB®

Engineered for fit, function, and leverage, these L-shaped shop-quality Torx compatible wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Torx compatible drivers at each end - Includes T6, T8, T10, T15, T20, T25, T30, and T40 - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization

Three of the most common Torx compatible wrench sizes in our classic 3-way design. The TWS-3 is useful for disc rotor bolts (T25), chainring bolts (T30), and hydraulic brake work (T10). TWS-3 FEATURES - T10, T25 and T30 Torx compatible set - Wrenches made from industrial tool steel, through hardened and tempered for long life

Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4T was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Bench Top Mount sits firmly on any flat surface - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)

Forged with Chrome Vanadium (CR-v) steel, precision ground, heat-treated, plated and polished. The PAW-6 opens to 24mm and features a laser engraved measurement scale and dipped blue handle for comfort.

The 15-inch SWB-15 is a forged steel breaker bar with a 3/8-inch square drive head that pivots 180º. Features a long, knurled handle, which is extremely useful when extra leverage is needed to remove stubborn fasteners.

Forged and machined, the ZP-5 is ideal for closely cutting zip ties and many other materials in tight spaces.

Park Tool's Crown Race Cutter Adaptor is used in conjunction with the CRC-1 Crown Race Cutting Tool (sold separately) to machine 39.8mm crown race seats (1.5” standard) on tapered forks with 1-1/8” steerer tubes. It includes a precision-machined adaptor body and a 39.8mm high-speed steel crown race cutter. The CRC-15 will work on forks with a maximum 1.5-inch taper of 4.25 inches.

A great shop accessory made to hold a wide variety of axles, spindles and any Park Tool Freewheel Remover/Lockring Tool. Made from precision extruded aluminum.

Park Truing Stand parts to get truing stands back into tip-top working condition. The TS-2TA.3 installs quickly and easily into Park Tool Professional Truing Stands — including the TS-2.2 & TS-2 — for full compatibility with thru axle hubs.

Park Cone Wrenches are made of durable tool steel to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Park's special Y-heads put more material where it's needed for excellent durability and strength. The 28mm size fits newer Shimano 20mm through-axles, as found on XT, XTR and Saint hubs. Most applications require at least 2 cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.

Park's Offset Brake Wrench utilizes a unique design that allows it to reach into tight areas that other wrenches cannot. The OBW-3 features a 14mm wrench on one end and the other end fits into a brake's tension springs to rotate the brake around its bolt for proper alignment. The OBW-4 features 10-, 11-, 12-, and 13-mm opening to fit most models of sidepull brakes.

Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.

Park Tool's SW-11 is a forged, double-ended spoke wrench designed to fit select Campagnolo wheels. Precision machined, plated and vinyl dipped for comfort and long life. It fits Campagnolo 5.5mm and 6.0mm hex spoke nipples.

The BKM-1.2 Hydraulic Brake Bleed Kit will bleed most models of mineral oil-based hydraulic bicycle disc brakes, including models made by Shimano®, Magura®, TRP®, Tektro®, Trick Stuff®, SRAM® DB8, Campagnolo®, Promax®, and Clarks®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKM-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, a bleed funnel, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: -  Two 20 mL syringes -  Two hose assemblies with shutoff clips -  One hose assembly with integrated fitting for bleed nipples such as those found on Shimano® mineral oil brake systems -  One open-ended hose assembly -  Bleed funnel with stopper -  Two 10 mm/12 mm universal bleed blocks -  Two 11 mm bleed blocks -  Two adjustable syringe holders -  M4 x 0.7 adapters — SRAM® DB8, Trick Stuff®, Campagnolo® (x2) -  M5 x 0.8 adapter — Formula™ Cura™, Tektro®, Hayes® (x2) -  M6 x 0.75 adapter — Magura® -  M6 x 1.0 adapters — universal (x2) -  M6 x 1.0 adapter — Promax® -  M7 x 0.75 adapter — Shimano® -  Hose compression sleeve — universal -  Fluid disposal bag -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKM-1.2 is for mineral oil-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For brakes using DOT fluid use the Park Tool BKD-1.2 Hydraulic Brake Bleed Kit — DOT.

"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings: • Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose • Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS • Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm • Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire • Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes Also included: • Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing • Guide magnet — routes guide cables through the frame from the outside"

Forged and precisely machined, the high leverage LP-7 Utility Pliers include an integrated cutting blade and soft touch grips.

Park's Tire and Tube Repair Kit is a riding essential. It features Park’s glueless Super Patch Kit and strong nylon Tire Levers for quick and easy flat repairs. The kit comes with 3 levers, 6 patches in a small container, and a piece of sandpaper (for roughing the tube to prepare it for patching).

The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.

Specially designed for crank bolts, freehub removals and pedal installs and removals, Park's Hex Tools are built for speed, leverage and comfort. Their super-precise hex heads and dual-density, ergonomic handle mean the HTs may soon become your new favorite tools.

Securely holds any of Park's TS-2, TS-2.2, and TS-2.2P Professional Wheel Truing Stands and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.

Designed and built specifically for a wide variety of bicycle Torx compatible work, the THT-1 is a set of eight common sizes of professional quality T-Handle star-shaped wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite Torx compatible set, the THT-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - T6, T8, T10, T15, T20, T25, T30 and T40 Torx compatible wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

Park's Tire Seating Tool is designed to quickly seat the bead on stubborn tires. During inflation some tire beads can slip below the rim edge and become difficult to pull out and align. The PTS-1 comes to the rescue with its non-slip jaws and vinyl-coated handles that provide plenty of leverage for pulling out the tire. Plus, it's adjustable to fit various tire widths.

Bicycle disc brake rotors can become warped from extensive use, excessive heat, or impact. Even new disc rotors may not always be perfectly straight, causing annoying pad rub and affecting performance. The Park Tool DT-2.2 is specially designed and precisely manufactured to gently adjust bent bicycle disc brake rotors. The DT-2.2 features one long slot and two short slots for maximum compatibility with any rotor design or thickness up to 2.5 mm. Constructed from high quality steel with a vinyl dipped handle for comfort. Compatible with rotors up to 2.5 mm thick

The SBK-1 is a professional level kit for installing and removing cartridge bearings in bicycle suspension pivots. A comprehensive set of 27 precision-machined hard-anodized guides enables compatibility with a wide range of bearing inner and outer diameters. Combined with our proven bearing press design, the SBK-1 quickly and easily pushes the old bearing out of the linkage and reinstalls the new bearing precisely and squarely. - Magnetic back plate for easy configuration and assembly - Organized in a convenient storage case Includes extractor cups/drifts for the following ODs: - 16mm - 17mm - 19mm - 20.6mm - 21mm - 22mm - 22.3mm - 24mm - 26mm - 28mm - 28.6mm - 30mm - 32mm - 35mm Includes extractor studs and pilots for bearings with the following IDs: - 8.5–9mm - 10mm - 12mm - 12.7mm - 15mm - 17mm - 20mm NOTE: For bearing extraction, the SBK-1 requires a minimum of 3mm of flat linkage structure outside the bearing to support the extractor cup/drift. For bearings without this flat structure, consider using the Park Tool SHX-1 Slide Hammer Bearing Extractor.

A worn chain shifts poorly and wears sprockets at an accelerated rate. Park Tool's Chain-Wear Indicator is a “go-no go” gauge designed to accurately indicate when a chain reaches .5% and .75%, the points at which most chain manufacturers suggest replacement. The updated CC-3.2 is longer, more accurate and features permanent measurement markings.

Never be left looking for an errant wrench when you have Park's Metric Wrench Set. It includes 12 high quality Park metric wrenches from 6 to 17mm in diameter, featuring both box and open ends. They are all forged from chrome vanadium steel, then chrome plated for durability and dipped in Park Tool blue vinyl for outstanding comfort and ease of use.

Park's Bottom Bracket Wrench has 2 ends to fit slotted bottom bracket adjusting cups and cups with raised 16mm wrench flats common on older English and less-expensive bicycles. Please ask if you have any questions whether this wrench is right for your repair.

Designed and built specifically for a wide variety of bicycle hex work the THH-1 is a set of eight common sizes of professional quality T-Handle hex wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite hex set, the THH-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - 2, 2.5, 3, 4, 5, 6, 8 and 10mm hex wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or over-sized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

Once you try on Park's Heavy Duty Shop Apron, there's no going back to standard aprons. The SA-3 is made from heavy 10-ounce cotton canvas and has two rows of bar tack reinforced pockets for stashing pens, parts, tools, etc. The special crossback design removes pressure from the neck for all day comfort and a nylon quick release makes the apron easy to adjust and take off. This sweet apron is a full 35-inches in length and the bottom 7-inches of the apron can be snapped up for a custom height fit. Plus, an embroidered Park Tool logo makes the apron as good looking (even when it's dirty) as it is functional.

Precisely machined for a perfect fit, this 8-notch tool removes and installs the lockring that retains front chainrings found on Bosch Gen 2 e-bike motors after the crank arm is removed. - Fits Bosch Active Line (chainrings less than 20 teeth), Performance Line and Performance Line CX models - For lockrings with 50mm outside diameter and 8 notches - Replacement for Bosch 0275009003 tool - Torque wrench compatible 3/8-inch square drive - Constructed of 4140 heat treated steel and plated for long life

Park Tool's versatile and durable 8oz Shop Hammer is a perfectly balanced striking instrument built for a wide variety of shop uses. - Forged steel, precision machined striking face - Non marring, replaceable composite tip - Fiberglass shaft with soft touch grip - 8oz (225g) Head - Length: 12" (30.5cm) - Steel striking face: 1" (25mm) diameter - Plastic face: 1-1/4" (32mm) diameter - Replacement tip: Part #293-8

Securely holds the TS-4 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.

Our iconic spoke wrenches have been a mainstay of our product lineup since we introduced them over 50 years ago. With their simple design and professional quality, they're still the favorite of bike mechanics around the world. Each Park Tool SW-6 is made in the USA, and is heat treated and nickel plated for long service. Park Tool spoke wrenches are vinyl dipped to indicate the size at a glance. • Sized for spoke nipples with 3.7 mm (0.146") wrench flats • This size can be found on some hub-drive e-bikes — always measure to be sure

12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.

A daily-use, shop version of Park Tool's world-famous CM-5.2 Chain Scrubber. The CM-25 features a super-tough die-cast aluminum case and handle, plus a unique brush/sponge replacement cartridge that makes it easy to keep it running smoothly and working properly. Park Tool's proven four-sided scrubbing action makes thoroughly cleaning chains quick and easy. A shop quality cleaner built to give years of constant use. - Proven chain scrubbing technology leaves chains sparkling clean - Durable A380 aluminum die cast case and removable handle - Dual-sided sponges and wicking pads to help reduce drips - Rotating brushes clean on all four sides of every link - Brush and sponge cartridge quickly and easily clicks in and out (RBS-25) - Locking cover with stainless steel hinge pins - Choose drip or immersion fluid application methods - 100% serviceable

Get those heads sealing like new and reduce compressor energy waste with Park Tool's Head Seal Kit. This kit will help get rid of that hissing sound you've been hearing when it has been too long since servicing your Park Tool INF-1 or INF-2 shop inflator. Kit includes: - 1 #1586 Presta Seal - 1 #1588 Schrader Seal - 2 #1576-2 O-rings for Shuttle-valve - 1 #1682-2 O-ring for INF-1 and INF-2 Head Adaptors

Park's Four-Sided Spoke Wrenches grip 4 sides of the spoke nipple so they offer an excellent grip and won't slip or round nipples when turning even the tightest spokes and/or aluminum nipples. These popular wrenches also have easy-to-hold vinyl-coated loop handles that are color-coded according to spoke size for easy identification. The loop handle makes them easy to hang on your tool board too.

Suspension maintenance and tuning require tools designed for a precise fit. The SKT-6 from Park Tools is a shop-quality set of six flat-faced sockets designed for use with common suspension fork fittings. Ideal for use with Park Tool Torque Wrenches, the 3/8-inch drive sockets are forged from tough chrome vanadium steel and chrome plated for lasting durability. - 24, 26, 27, 28, 30, 32mm flat-faced sockets - All sockets are 3/8" drive - Note: 27mm socket is tapered for better access on Suntour suspension forks

The FCT-1 is a versatile tool for easy and damage-free removal of suspension fork caps, which can be difficult to remove by hand when overtightened. The six sides of the FCT-1 correspond to the most popular fork cap designs for a snug and secure fit. Compatible with select suspension top caps from the following manufacturers: - FOX® - RockShox® - DVO® - Marzocchi® - Öhlins® NOTE: Do not use the FCT-1 to overtighten fork caps. Always follow manufacturer recommendations for fork cap installation.

The BBT-16 removes and installs the self-extracting/one-key release caps on SRAM and RaceFace cranks with a 16mm hex hole. Features investment cast steel construction and an option to use 8mm hex for better leverage.